Tekin RS Gen2/Redline Gen3 10.5T Brushless Motor/ESC Combo
The RS GEN2 brushless speed control is the next generation in intelligent operating motor drive technology. Continuing the proven award-winning legacy of the RS family, the GEN2 is fitted with todays state of the art components. The RS GEN2 delivers what racers require; reliability, precise control and unmatched power handling capability.
Packed with new features, the RS GEN2 delivers a programmable high-voltage BEC, an EZ Access Port for HotWire communication and Data logging capabilities in a small sized package. Rated for 8.5 turn motors and higher, the GEN2 is the perfect ESC for both experienced and new racers. Couple the RS GEN2 with a Redline GEN2 brushless motor for the ultimate package in race equipment.
D2 is Tekin's hybrid sensorless / sensored drive technology, fusing the reliability of sensored with the efficiency of sensorless. D2 provides perfect starts and smooth low rpm operation while allowing for dynamic timing adjustments and running efficiency at higher rpms.
ESC Features:
- Ultra-smooth and Precise Throttle and Braking Control
- Compatible with Sensored/Sensorless Brushless and Brushed Motors
- Easily Access Programming, Anywhere, Anytime
- Datalogging Capability
- High Voltage Programmable BEC
- EZ Access HotWire Programming Port
- HotWire PC Interface for Advanced Programming and Updating
- D2: Dual Drive Mode Technology
- On-Board Temperature Indicator
- HDAC: High Density Copper PCB's
- Sensor Plug for Precise Commutation with all Motors
- Gold-plated Solder Posts for Easy Wire Replacement
- Self Test Diagnostics and Factory Reset
- Pit Tune Mode
- DGF2: Digital Glitch Filtering V2
- QuickTune Programming
- One-Touch Radio Calibration
ESC Programming Features:
- High Voltage BEC (6.0v/7.4v)*
- Drag Brake (13 steps)
- Brake / Reverse Strength (13 steps)
- Current Limiter (none + 12 steps)
- Neutral Width (13 steps)
- Timing Profiles (5 preset - 2 custom*)
- Adjustable Throttle and Brake Minimums
- Custom Throttle Curves
- Motor/Reverse Type: Brushless, Brushed, No Rev, Rev Delay
- Voltage Cutoffs (none, 2S, 3S, Custom)
- Timing Boost and Turbo when used with Hotwire
- ROAR Race Spec "Blinky" Mode
- Save, Load and Share custom ESC setup files
- Extensive Tuning via Tekin HotWire PC Interface
*Requires HotWire Sold Seperately
ESC Specs:
Controls: Forward/Brake/Reverse
Input Voltage: 4-9 Cells, 2S-3S Lipo
BEC: 6.0v / 7.4v 5.5amps
Motor Limit Brushless Mode: 8.5 Turn, 540 2-pole (36mm)
Motor Limit Brushed Fwd Only Mode: 10 Turn
Motor Limit Brushed Fwd/Rev Mode: 12 Turn
Timing Profiles: 7 choices (on board)
Brushed Modes: Fwd Only, Fwd/Rev, Rev Delay
Brushless Modes: Fwd Only, Fwd/Rev, Rev Delay
Dimensions: 1.0 x 1.3 x .51in (25.4 x 33 x 12.9mm)
Weight: 2.0oz / 48g with wiring
Motor Specs:
Tekin’s third generation motors are re-engineered from the ground up resulting in a smaller, lighter and faster sensored motor. On Road or Off, the new GEN3 handles the task in stride, delivering the smooth power across all RPMs that you’ve come to expect from a Tekin motor. Much more than a re-hash and new look, the GEN3 Redline Sensored Motor is now ready for any situation and able to create the speed you need to win.
Specs:
- Input Voltage: 2S - 3S lipo
- Weight: 158g / 5.6oz
- Shaft Dimensions: 3.2mm (1/8") x 15.3mm
- Motor Diameter: 35.85mm / 1.40"
- Motor Length: 48.5mm / 1.909"
- Bearing Dimensions: Front: 4 x 13 x 5mm / Rear: 1/8 x 3/8 x 5/32"
- Rotor Size: 12.5mm
Features:
- CNC Machined T 6061 Billet Aluminum Heat Sink Can
- Neodymium Sintered Magnet
- Precision Engineered for Maximum Energy Conversion
- High Purity Copper Windings Maximize Conductivity
- Low Resistance, High Power Solder Tabs
- Dual-Plug Sensor Wire Harness for all Sensored and Sensorless systems
- Anodized End-bell plates maximize corrosion and wear resistance
- High RPM precision bearings
- Rebuild-able Design
- Solder-less Sensor PCB replacement
- Adjustable Timing
